Welcome to the LRS Help Center
  1. LRS Support
  2. Self Help
  3. Reprogramming LRS Pagers

Programming LRS Guest Pagers by Transmitter Type

Menu

    The way to program Guest Pagers is based on the type of transmitter you have.

    - Below is a list of How to Guides, separated by which model transmitter you have to page the pagers.

    - When programming pagers, it is always important to have all pagers at the location on, or in their charging base(s) so that you easily reprogram one pager at a time.

     

    Reprogramming Guest pagers with the TX-9561MT 

    1. To ensure your LRS Transmitter is set to LRS Guest Mode, press 9-9-6-PROG. If LRS Guest Mode is turned on, only LRS Coasters and Paddle Pagers can be paged.
    2. Remove only the Pager that you want to reprogram from the charger.
    3. Allow the Pager to complete the vibration and flashing sequence.
    4. Enter that Pager’s number (from 1-799) and press PROG twice. (Example: For Pager #20, press 2-0-PROG-PROG).
    5. Be sure to hold the pager about arm's length away from the transmitter while programming it.
    6. The red LED in the top right corner of the transmitter will light up once.
    7. The pager will flash  and / or vibrate to indicate it received the programming. On pager models with the LED number display, the new number will be shown.
    8. Test the pager by entering the new pager number and pressing Send.
    9. Repeat steps 2-7 for additional pagers that you would like to program more pagers.

     

    Reprogramming Guest pagers with the TX-9560MT 

    1. To ensure your LRS Transmitter is set to LRS Guest Mode, press 9-9-6-PROG. If LRS Guest Mode is turned on, only LRS Coasters and Paddle Pagers can be paged.
    2. Remove only the Pager that you want to reprogram from the charger.
    3. Allow the Pager to complete the vibration and flashing sequence.
    4. Enter that Pager’s number (from 1-799) and press PROG twice. (Example: For Pager #20, press 2-0-PROG-PROG).
    5. Be sure to hold the pager about arm's length away from the transmitter while programming it.
    6. The red LED in the top right corner of the transmitter will light up once.
    7. The pager will flash  and / or vibrate to indicate it received the programming. On pager models with the LED number display, the new number will be shown.
    8. Test the pager by entering the new pager number and pressing Send.
    9. Repeat steps 2-7 for additional pagers that you would like to program more pagers.

     

    Reprogramming Guest Pagers with the Freedom Transmitter Types

    Models: TX-7400A, TX-7460, or TX-7470 / TX-7471

    1. Place all pagers to be reprogrammed on or in one charging base, leaving a second base empty if you have two or more bases to use.
    2. On the transmitter keypad, press SETUP and enter Password 31337.
    3. Press F2 (DN).
    4. Press 1 (1: Program).
    5. Press 1 (1: Prg Pager).
    6. Press 1 (1: Guest Pagers).
    7. Choose (1: Coaster or 2: Paddle).
    8. Choose (1: Non-Alpha or 2: Alpha).
    9. If the pager should vibrate, press F1 for Yes otherwise, press F4 for No.
    10. Enter the pager number for this pager.
    11. Remove the pager to be programmed from the charger.
    12. When the pager is done flashing and / or vibrating, press ENTER.
    13. The pager will flash 1 time to indicate it is has been re-programmed and the new number will be displayed on the pager screen.
    14. The transmitter will ask you whether the pager beeped or vibrated - we know that the pager did not do that, its OK, if it flashed and shows the pager number, press F1 for Yes. (If No, press F4 and you will be prompted to retry the reprogramming sequence).
    15. Place the reprogrammed pager on the second charging base or on the very bottom of the first charging base.
    16. The transmitter will then ask if you would like to program another pager.
    17. If you would like to program another pager, press F1 for Yes, if you are done, press F4 to complete the process.
    18. If you chose Yes to program another pager, the transmitter will take you back to step 10 to enter the number that the next pager will be programmed as.
    19. When you are finished programming all pagers intended, remove the newly reprogrammed pagers from the charging base and page each one to test that they are the correct number and receive a page.
    20. Reprogram any that do not page.

     

    Reprogramming Guest Pagers with the TX-9550LCMG

    1. To ensure your LRS Transmitter is set to LRS Guest Mode, press 9-1-6-PROG.
    2. Remove only the Pager that you want to reprogram from the charger.
    3. Allow the Pager to complete the vibration and flashing sequence.
    4. Enter that Pager’s number and press PROG. (Example: For Pager #23, press 2-3-PROG).
    5. The pager will flash and / or vibrate to indicate it received the programming. On pager models with the LED number display, the new number will be shown.
    6. Test the pager by entering the new pager number and pressing Send.
    7. Repeat steps 2-6 for additional pagers that you would like to program.

     

    Powered by Zendesk